Item 1 1. When the set contents of a mode were changed by function selection, the functions of that mode also change. Check the set contents as described in steps 2 to 7 and change the setting based on the entries in the Table 1 check field. For the factory settings, refer to the indoor unit installation manual. This step is unnecessary for single refrigerant system. Refrigerant address display To connect the remote control cord, peel 6mm of coating.
SLIM packaged air conditioners. Please read this manual thoroughly and install the remote controller accordingly. For information on how to wire and install the air conditioning units, refer to the installation manual.
After the installation, hand over this manual to users. Any dew, moisture, insects entering the unit may cause an electric shock or a malfunction. When registered using the E [ ] button, the registered indoor unit begins fan operation. When you want to know the location of the indoor units of the unit address No. When the unit address No. Ex When refrigerant address 00, unit address No. The refrigerant address and unit address No.
After a while, the mode No. Use standard wires in compliance with the current capacity. A failure to this may result in an electric leakage, heating or fire. Wire so that it does not receive any tension. Tension may cause wire breakage, heating or fire.
This setting cannot be made with Mr. SLIM air conditioners. Do not install in any place where acidic or alkaline solution or special spray are often used. Doing so may cause an electric shock or malfunction. When installing the remote controller in a hospital or communication facility, take ample countermeasures against noise. Inverters, emergency power supply generators, high-frequency medical equipment, and wireless communication equipment can cause the remote controller to malfunction or to fail.
Radiation from the remote controller may effect communication equipment and prevent medial operations on the human body or interfere with image transmission and cause noise. English is set in this manual. Set it to the unit address No. The maximum voltage that can be applied to the remote controller is 12V.
The remote controller may be damaged or may generate heat and cause a fire. Press the D button. Press the Press the E button.
E button. The unit address No. NOTE Timer operation stops when the display for remote controller function selection is changed to the normal one. Any deficiency caused by your own installation may result in an electric shock or fire. Refrigerant address display Normal display Display when the air condition is not running First, hook the cover to the two upper claws and then fit it to the remote controller.
End To remove the cover, insert a minus screwdriver into one of the open slots, and move it in the direction of the arrow shown in the figure. SLIM packaged air conditioners.
Please read this manual thoroughly and install the remote controller accordingly. For information on how to wire and install the air conditioning units, refer to the installation manual. After the installation, hand over this manual to users. Item 2 Item 1 1. There is no polarity. Change the setting when needed.
Connect the remote control cord to the remote controller terminal block. When the set contents of a mode were changed by function selection, the functions of that mode also change. Check the set contents as described in steps 2 to 7 and change the setting based on the entries in the Table 1 check field. For the factory settings, refer to the indoor unit installation manual. This step is unnecessary for single refrigerant system. Function Selection Remote controller switching is necessary.
Install the lower case on the switch box or directly on the wall. When using the switch box Switch box for two units Seal the remote control cord lead-in hole with putty. NO Change refrigerant address and unit address No.?
Check the transmission line and the other remote controllers. In this case, the send data was disturbed by the noise, etc. Check the transmission line. Approximately 30 seconds later, the remote controller returns to the state before remote controller check. Ending function display Press buttons A and B simultaneously. The use of this controller for with other systems or for other purposes may cause malfunctions. To avoid discoloration, do not use benzene, thinner, or chemical rag to clean the controller.
To clean the controller, wipe with a soft cloth soaked in mild detergent that is diluted with an appropriate amount of water, and wipe down with a wet cloth followed by a dry cloth. Do not use the detergent straight. To avoid damage to the controller, provide protection against static electricity. Take appropriate measures against electrical noise interference when installing the air conditioners in hospitals or facilities with radio communication capabilities.
Inverter, high-frequency medical, or wireless communication equipment as well as power generators may cause the air conditioning system to malfunction. Air conditioning system may also adversely affect the operation of these types of equipment by creating electrical noise. To avoid malfunctions, do not bundle power cables and signal cables together, or place them in the same metallic conduit. Do not install the controller on the control panel door. Vibrations or shocks to the controller may damage the controller or cause the controller to fall.
Solderless terminals may come in contact with the circuit board and cause malfunctions or damage the controller cover. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. This appliance is not intended for use by persons including children with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance. This appliance is intended to be used by expert or trained users in shops, in light industry and on farms, or for commercial use by lay persons. To avoid damage to the controller, use appropriate tools to install, inspect, or repair the controller.
To prevent malfunctions, do not remove the protective film or the circuit board from the casing. Hold the cables in place with clamps to prevent undue force from being applied to the terminal block and causing cable breakage. SLIM air conditioner A control type. The wiring also differs with the system configuration.
Check the system used. The numbers 1 to 4 in the figure correspond to items 1 to 4 in the following description. Connect to the terminal block at the bottom of the remote controller case. The remote controller wiring depends on the system configuration. Check the system configuration. Wire the remote controller as shown in the example below. The numbers 1 to 3 in the figure correspond to items 1 to 3 in the following description.
For more information, refer to the outdoor unit installation manual. The terminal block has no polarity. Connect the remote controller to an arbitrary indoor unit of each refrigerant system you want to group.
Also, when the Main unit is the simultaneous multi type, always satisfy the conditions of 1 above. When two remote controllers are connected to one group, set the Main remote controller and Sub remote controller. If so connected, the system will not operate normally.
Only one wire can be connected to the remote controller terminal block. This remote controller is for the wall installation. It can be installed either in the switch box or directly on the wall. When performing direct wall installation, wires can be thread through either back or top of the remote controller. Install the remote controller switch box on the site where the following conditions are met.
Sensors to monitor indoor temperature are on the indoor unit and on the remote controller. When the room temperature is monitored with the sensor on the remote controller, the built-in sensor on the remote controller monitors the room temperature. When using the sensor on the remote controller, follow the instructions below. If wires are routed, the sensor cannot measure accurate indoor temperature.
If the following conditions are met, the use of the temperature sensor on the indoor unit is recommended. Note: When temperature changes rapidly, the temperature may not be detected accurately.
Do not install the controller in a place where the difference between the remote controller surface temperature and the actual room temperature will be great. If the temperature difference is too high, room temperature may not be adequately controlled. To reduce the risk of malfunctions, do not install the controller in a place where water or oil may come into contact with the controller, or in a condensing or corrosive environments.
To reduce the risk of malfunctions and damage to the controller, avoid installing the remote controller on an electrically conductive surface, such as an unpainted metal sheet.
0コメント