No modifique de ninguna manera el enchufe. Nos gusta mucho limpiar y nos entusiasma compartir uno de nuestros productos innovadores con usted.
NOTA: Deje que las partes se sequen completamente antes de devolverlas a la aspiradora para usarlas. Permita que se sequen los componentes antes de volver a armar el tanque de suciedad.
Page 22 Hay una grieta o un agujero en la Si hay una grieta u orificio, solicite una manguera principal. Cambie el cepillo giratorio. Page 31 « clic ». Page 36 Rendez-vous sur le site www. Print page 1 Print document 36 pages. Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR. Don't have an account? Sign up! Restore password. Upload manual.
Upload from disk. Upload from URL. There will be a click when fully installed. The Long Reach Dusting tool does not store on the vacuum select models. Take cord and wrap around the two cord wraps located on the back of the vacuum.
Highest Setting: For high pile and most shag carpet. Adjust to high setting if difficult to push. NOTE: For optimal carpet cleaning performance, adjust to the lowest practical setting. If your vacuum is difficult to push, or is pushing larger debris, adjust to the next higher setting. The floor brush will continue to rotate while you use your vacuum for above floor cleaning.
To prevent carpet damage, do not lean on the vacuum or let the power foot tilt forward. With the vacuum in upright position, remove the lower hose end from the foot of the vacuum and from both hose clips.
Attach desired tool by firmly inserting the tool into the hose end. Use rotation brush action for small flat areas such as stairs and cushions. Press gently down and pull towards you in raking motion; too much pressure will cause brush to stop rotating. The brush easily stores on the handle. For best performance, empty when the dirt reaches the full line on the container. Remove tank by pressing the release button on the tank handle. Visually check the pre-motor filter located directly under the dirt tank.
If there is debris, follow filter instructions in the maintenance section. Grasp handle on back of the tank with one hand and the top handle with the other. Over a trash container, twist the top handle counterclockwise until the latches release. Pull the top handle piece straight from the dirt tank.
Empty contents of dirt tank into trash container, and gently shake the top handle piece to remove build up. NOTE: If you notice excess build up around the top of the tank, before removing top piece, gently tap the tank to allow contents to settle. Place the top handle piece straight downward into the dirt tank. Align the latch arrows and gently twist clockwise.
When fully assembled, the tank will click into place. Replace the tank back onto the vacuum — the tank will click into place when fully installed. To maintain best performance, check and clean your filters regularly.
If you notice a decrease, in performance check your filters by following. It is recommended to check your filters as often as you check and clean your dryers lint trap. The pre-motor filter is located directly under the dirt tank. Remove dirt tank by pressing release button and remove from vacuum.
Grasp filter and remove from the vacuum. While holding over trash, gently separate layers of filter being careful not to rip filter layers and shake out excess debris. Filter can be rinsed in warm water. Allow the filter to air dry completely before replacing. If you notice the filter is damaged, reference the replacement parts section to order a new filter. Do not operate vacuum with damp or wet filters or without all filters in place. The post-motor filter is located on the front of the vacuum near the height adjust knob.
Remove filter door by pressing latch downward. It is easiest to have the vacuum fully reclined to access the filter. Remove the filter by grasping the. The filter can be washed in warm water with mild detergent. Replace filter in unit with handle facing you. Replace the door by hooking the bottom into the grooves and rotate towards unit snapping into place.
Turn power OFF. Unplug vacuum cord from electrical outlet. Place handle in low position, remove hose end from foot and turn the vacuum over so bottom side is facing up. Using a long Phillips screwdriver remove the 7 screws and rotate unit back to front. You also may remove the height adjustment plate by gently prying each latch on the sides free from the foot and rotate out to remove.
If removed, replace the height adjustment plate by aligning the ends opposite of the wheel to the latches and push down. Lift top over straight up and set aside. Grasp rotating floor brush at both ends and lift up and away to remove. Clean strings, hair and other debris from rotating floor brush, motor pulley and drive belt areas.
With rotating brush removed steps of checking rotating floor brush and drive belt , grasp old drive belt and remove from motor pulley. Discard old drive belt. Place new drive belt over motor pulley and stretch other end over rotating floor brush in the space between the bristles. Place ends of rotating floor brush down.
Turn rotating floor brush by hand in the direction of the motor pulley. If properly installed, drive belt will center itself on rotating brush. Reposition top cover and rotate on back side. Empty the dirt tank by following the instructions in the previous Operations section. With top handle piece removed you can wash the dirt tank in warm water with mild detergent. Allow tank to air dry completely before reassembling. Clear any debris from the top piece. Grasp top handle and the round separator piece and twist counterclockwise to release.
The separator can be washed in warm water with mild detergent. Make sure there is no dirt build up between the openings around the separator. Allow top handle piece to dry completely before reassembling. Replace the separator back into the top handle piece by aligning the tabs and turning clockwise to lock into position.
Empty and clean dirt tank, ensuring there is no dirt around the separator. With dirt tank removed, check the suction inlet located on the body of the vacuum, remove any debris.
Remove the lower hose end by gently pulling out of vacuum base. Unclog with long, narrow object such as broom stick. If the clog persists, follow steps for checking rotating floor brush on page 10 and inspect the air passageway for obstructions. Other maintenance or service not included in the manual should be performed by an authorized service representative. Contact us directly at This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.
If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL Consumer Care by E-mail, telephone, or regular mail as described below. This warranty applies to product used for personal, and not commercial or rental service. This warranty does not apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair, or any other use not in accordance with the User's Guide is not covered.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Some states do not allow limitations on how long an implied warranty last so the above limitation may not apply to you. NOTE: Please keep your original sales receipt.
It provides proof of date of purchase in the event of a warranty claim. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Powertrak Bissell Powertrak User Manual Download for 1. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, have it repaired at an authorized service center.
Safety Instructions. Handle 2. Dirt Tank Release Button 4. Dirt Tank 5.
0コメント